[lug] Partitioning and modem problems

[Eric Weber]

A long time ago I tried using kppp to manage my connections.
Unfortunately, I got the same error message.  I didn't figure out what was
wrong, but I could set up the connection manually using minicom/pppd.
Have you tried using minicom or seyon to see if you could access the
modem?

Additionally, if the modem really is on COM5, makedev may be of use.

On Sun, 18 Jun 2000, Mike McCallister wrote:

> A little more info that may well point in a good direction. I 
> double-checked the COM port that Windoze says the modem is using. Device 
> Manager reports the modem is on COM5. So I booted back to Linux and tried 
> to run setserial again (BTW, it's truly wonderful that it remembers my last 
> command even after logging out!!), changing ttyS2 to ttyS4 to reflect the 
> "new" port. Setserial reported there was no such port (as ttyS4/COM5?).
> 
> I then rechecked /proc/ioports. I had earlier written down that 
> proc/interrupts called the device using IRQ9 as usb-uhci. Well, 
> proc/ioports notes that the usb-uhci device is using ef80-ef93. Meanwhile, 
> lspci says the modem is using IRQ9 and I/O ports at dfe0. So, something 
> tells me that there is either a conflict, or the modem port is not set 
> properly. Is this right?
> 
> Thanks yet again!
> 
> Mike
> 
> At 07:38 PM 6/17/00 -0600, you wrote:
> >Mike McCallister wrote:
> > >
> > > Greetings all!
> > >
> > > I was finally able to install Corel Linux last week, and am most thrilled
> > > to be running a fairly stable dual-boot Win98/Linux system at this time.
> > >
> > > There are two nagging and critical problems that I can't seem to figure
> > > out, though.
> > >
> > > First, I had left 10GB (of my single Western Digital 20GB drive) for Linux
> > > partitions. I asked the Corel install program to use and format all the
> > > free space on the drive. It made a 1.7GB partition for itself and a 125MB
> > > swap space, but left the remaining ~8.3GB alone. I can't seem to make any
> > > new ext2 partitions.
> > >
> > > I have Partition Magic 5.1 and it tried unsuccessfully to make new Linux
> > > partitions (ideally, I'd like to have one large /usr partition to store
> > > apps on and one data partition for docs, etc.). I also tried running Linux
> > > FDisk from the Corel Console, but it says there's no space left when I ask
> > > it to create a new partition! Here is how Linux FDisk reports the partition
> > > table (PM reports slightly different numbers):
> > >
> > > hda1: Starts on Cyl 1, Ends on 374. Blocks: 3004125+. ID: b. Win95/FAT32
> > > (the Windows C: drive)
> > > hda2: 1678-2482, Blocks: 6466162+. ID: f. Win95 Extended (LBA) PM created
> > > this one
> > > hda3: (Boot partition) 375-598. Blocks: 1799280. ID: 83 Linux Native (this
> > > is where Corel's root is)
> > > hda4: 599-614. Blocks: 128520. ID: 82. Linux Swap (created by Corel)
> > > hda5: (my Windows D: partition in the DOS extended part). 1678-2431.
> > > Blocks: 6056473+. ID: b. Win95/FAT32
> > > hda6: (Windows E:, FAT16). 2432-2482. Blocks: 409626. ID: 6. DOS 
> > 16-bit >=32MB.
> > >
> > > When FDisk verifies the partition table, it reports 17077281 unallocated
> > > sectors. Physically these sectors are located between hda4 and the DOS
> > > extended partition (hda2/hda5). Is this my problem?? BTW, I also tried
> > > installing GNU Parted, but I'm missing some dependencies.
> > >
> > > The other problem is getting the internal modem to work. This is a brand
> > > new Dell system. When I ordered it about three months ago, I confirmed with
> > > the guy that this was a hardware-based modem, and that it would work with
> > > Linux. I've since double-checked with the Dell website and they also assure
> > > me that my modem will work with Linux. I also downloaded a Red Hat modem
> > > driver (yes, I recognize that the driver may not work with the Debian-based
> > > Corel distro). Meanwhile the Windows Device Manager reports that the modem
> > > is a USRobotics 56K Voice PCI (and I know that PCI modems can be
> > > problematic). The Dell spec sheet calls it a 3Com PCI Telephony modem--now
> > > that I look at it again, this is also a bad sign. The bottom line is that
> > > every time KPPD queries the modem, "Sorry, modem is busy" is the reply.
> >
> >On the pci modem side, I have one that works great. The problem is
> >usually that the serial port you have assigned to it doesn't have the
> >correct irq assigned as well, which is where setserial helps.
> >
> >My modem is being set to irq 17, and so I have this line in rc.local to
> >match this irq to the serial port:
> >/bin/setserial -v /dev/ttyS2 uart 16550A port 0xafe0 irq 17 spd_normal
> >skip_test
> >
> >A few things you can do to find what your modem wants are in /proc/.
> >View /proc/ioports, and /proc/interrupts
> >
> >The remaining info can be found with lspci or lspci -v. If you don't
> >have this program, check http://las.978.org
> >
> > >
> > > TIA for any ideas.
> > >
> > > Mike McCallister
> > >
> > > _______________________________________________
> > > Web Page:  http://lug.boulder.co.us
> > > Mailing List: http://lists.lug.boulder.co.us/mailman/listinfo/lug
> >
> >_______________________________________________
> >Web Page:  http://lug.boulder.co.us
> >Mailing List: http://lists.lug.boulder.co.us/mailman/listinfo/lug
> 
> 
> 
> Mike McCallister			4325 Comanche Drive, #3
> ProTek Writing Services		Boulder, CO 80303-3618
> mmccallister at reporters.net		"Translation from the Geek a specialty"
> Phone: (303) 554-7533			Fax: (248) 282-0532
> 
> 
> _______________________________________________
> Web Page:  http://lug.boulder.co.us
> Mailing List: http://lists.lug.boulder.co.us/mailman/listinfo/lug
> 

Eric Weber
-------------------------------
Department of Mathematics
Texas A&M University
http://www.math.tamu.edu/~weber