[lug] Re: SB AWE32 Errors

[SoloCDM]

"D. Stimits" stated the following:
> 
> SoloCDM wrote:
> >
> > "D. Stimits" stated the following:
> > >
> > > SoloCDM wrote:
> > > >
> > > > I found the following modules for a Creative SB AWE32, with kernel
> > > > 2.2.14-15:
> > > >
> > > > /sbin/modprobe sound; /sbin/modprobe isapnp; /sbin/modprobe
> > > > joy-creative; /sbin/modprobe joystick; /sbin/modprobe snd-card-sbawe;
> > > > /sbin/modprobe snd-midi; /sbin/modprobe snd-mpu401-uart;
> > > > /sbin/modprobe snd-hwdep; /sbin/modprobe snd; /sbin/modprobe snd-pcm;
> > > > /sbin/modprobe soundcore; /sbin/modprobe snd-sb16-csp; /sbin/modprobe
> > > > snd-sb16-dsp; /sbin/modprobe snd-mixer; /sbin/modprobe snd-opl3;
> > > > /sbin/modprobe snd-wavefront-synth; /sbin/modprobe awe_wave;
> > > > /sbin/modprobe snd-hwdep; /sbin/modprobe snd-card-sbawe; /sbin/insmod
> > > > opl3; /sbin/insmod sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x330;
> > > > /sbin/insmod uart401
> > > >
> > > > My sound worked perfectly with kernel 2.0.36.  I have my CDROM
> > > > connected to the IDE controller card.  Every time I run sndconfig
> > > > with(out) global $DISPLAY environment variable, as per instructions,
> > > > I get the following errors:
> > > >
> > > > Don't know what to do with CONFIGURE CTL0044/941569 (LD 2 on or
> > > > around line 353 /etc/isapnp.conf:353 -- Fatal - Error occurred
> > > > parsing config file --- no action taken
> > >
> > > FYI, this is not a module error. This is for setting up plug-n-play ISA
> > > cards so that their hardware settings can match what either the kernel
> > > or the modules are set to use. I don't know if maybe the version of
> > > isapnptools also required a change/upgrade when going from the old 2.0.x
> > > to 2.2.x. You might want to post about a half dozen lines before and
> > > after line 353 (and mark 353) for /etc/isapnp.conf. Plus back it up so
> > > you can experiment, e.g., rerun isapnpdump and edit again.
> >
> > I didn't upgrade from 2.0.x to 2.2.x.  I overhauled the entire disk --
> > formatted the disk, installed new OS, which included kernel 2.2.x.  I
> > incorporated configurations from the old OS by modifying them to fit
> > the present platform.  I used sndconfig to create /etc/isapnp.conf.
> >
> > > > What must be done to fix this problem?
> 
> It sounds like sndconfig is broken. Is the sound card in fact an ISA
> slot, plug-n-play card? What are the lines surrounding the error line of
> /etc/isapnp.conf? I would still guess that sndconfig is reading this
> file but it is generated by isapnptools (I assume since the file is
> there and not copied from the old install that isapnptools was
> installed).

Here's the lines gathered around line 353:

# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
#
(CONFIGURE CTL0044/941569 (LD 2
#     ANSI string -->WaveTable<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0620
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))

#     End dependent functions
 (NAME "CTL0044/941569[2]{WaveTable           }")
# (ACT Y)
))


Note: When you reply to this message, please include the mailing
      list/newsgroup address in Cc: and my email address in To:.

*********************************************************************
Signed,
SoloCDM